Notifications
Clear all
Search result for: WA 0812 2782 5310 Rincian Pembangunan Rumah 1 Lantai Tinggi 5 Meter Terpercaya Kalasan Sleman
| # | Post Title | Result Info | Date | User | Forum |
| Answer to: DMM in mA mode causes ~0.6 V drop — normal burden voltage? How can I minimize it? | 12 Relevance | 4 months ago | nathan | Theoretical questions | |
| Yes, the 0.6 V drop you’re seeing is the Meter’s burden voltage, which is the voltage lost across the DMM when it measures current. In mA mode, the Meter places a small internal shunt resistor (and often a fuse or protection components) in series with your circuit to sense current, and this resistance causes a voltage drop equal to V=I×Rmeter. For example, a 0.6 V drop at 60 mA means the Meter adds about 10 Ω in series, which can significantly affect low-voltage circuits by reducing the actual voltage reaching your load. To minimize this, you can use an external low-value shunt resistor and measure the voltage across it with the DMM in voltage mode, then calculate current using I=V/RI = V/RI=V/R. Alternatively, use a dedicated low-burden current sense amplifier or sensor such as the INA219, a DC clamp probe that measures current without inserting resistance, or the Meter’s 10 A input (which usually has much lower internal resistance) if the current is within safe limits. These methods help keep the measurement accurate without disturbing the circuit’s operating voltage. | |||||
| Answer to: Is it safe to use the multimeter’s amp setting on live circuits? | 12 Relevance | 5 months ago | Neeraj Dev | Equipments | |
| Definetly not, Dont switch to amps or move the red lead to the A/10A jack while your probes are on a live circuit. In A mode the Meter is basically a short; flipping to it or probing voltage with the lead in A can blow the fuse, make an arc, or worse. Set the Meter and leads with power off, break the circuit, insert the Meter in series, then power up. For mains, use a clamp Meter; for 12 V high-current systems be extra cautious or use a clamp/shunt. And always move the red lead back to V when you’re done to avoid the classic “next-time short.” | |||||
| Answer to: Is it safe to use the multimeter’s amp setting on live circuits? | 12 Relevance | 8 months ago | cooper | Equipments | |
| ... of wire—it has very low resistance. If you try to connect it across a live circuit (like you would for voltage), you're basically shorting the power source, and that can result in Blown fuse in the Meter (if you're lucky), Arcs or sparks. So, If you dont WAnt that Always power off the circuit before measuring current. Break the circuit and insert the Meter in series, making sure the probes are in the correct ports—especially the high current port if you're measuring above ~200mA. Once everything's connected, power on the circuit, take your reading, and t ... | |||||
| RE: what is "Display count" in a multimeter? | 9 Relevance | 12 months ago | Admin | Equipments | |
| Not quite—a 6000-count Meter doesn’t extend the 2V range to 5.999V. The range is fixed by the multimeter, not the count. In the 2V range, both 2000- and 6000-count Meters typically max out at 1.999V. A 6000-count Meter would show up to 5.999V only if it's on a 6V range, not 2V. So, a higher count means better resolution, but the voltage range itself stays the same unless the Meter has a higher range setting. | |||||
| Answer to: Multimeter continuity beeps with no contact — false positives? | 6 Relevance | 8 months ago | Harper | Equipments | |
| This usually happens due to the high sensitivity of the multimeter’s continuity mode. Some Meters are designed to beep even with very low resistance, which means slight contact, moisture, or even nearby conductive surfaces can trigger a false beep. However, that's not the only cause. Sometimes, while testing components like Semiconductors or capacitors, residual charge or leakage paths within the component can also cause the Meter to falsely detect continuity. In such cases, the beep doesn't necessarily indicate a true short—it could just be the Meter reacting to a small voltage or current still present in the circuit. | |||||
| Multimeter continuity beeps with no contact — false positives? | 3 Relevance | 8 months ago | CircuitFlow | Equipments | |
| Hi everyone, While checking continuity with my multimeter, I sometimes get beeping sounds even when the probes aren’t actually touching the wires.It seems like a false reading.Could this be due to stray capacitance, interference, or a faulty Meter? | |||||
| Is it safe to use the multimeter’s amp setting on live circuits? | 3 Relevance | 8 months ago | techy ishan | Equipments | |
| I’ve seen WArnings about using the current (amp) setting on a multimeter, and I WAnt to be cautious. I understand that to measure current, the Meter has to be placed in series with the load. But I’m unsure about the risks involved when doing this on a live circuit, especially with higher voltages like AC mains or even 12V DC systems with decent current. Is it safe to switch to the amp mode while the circuit is powered? | |||||
| Answer to: Can measuring current the wrong way damage my multimeter? | 3 Relevance | 8 months ago | TechTalks | Equipments | |
| Yes, if you measure current like voltage (in parallel), you can short the circuit and blow the multimeter fuse, or worse, damage it. Also, if the probe is left in the current port and you try to measure voltage, it creates a short path and can seriously damage the Meter or the circuit. Always switch the probe back to the voltage port and check your dial setting before measuring. | |||||
| Answer to: How to Measure Capacitance with a Multimeter? | 6 Relevance | 8 months ago | Paul | Equipments | |
| ... gives inaccurate results. 2. Discharge the capacitor safely: 3. Use a resistor (e.g., 1kΩ, 1W) across the leads. 4. Avoid shorting large electrolytics directly — they can spark or get damaged. 5. Set your multimeter to capacitance mode (⏀). 6. Connect the probes to the capacitor leads. Polarity doesn't matter for film or ceramic caps; for electrolytics, follow Meter instructions. 7. WAit a few seconds for the reading to stabilize — especially for high-value caps. Hope this helps! | |||||
| Answer to: How to Measure Capacitance with a Multimeter? | 6 Relevance | 8 months ago | Amelia | Equipments | |
| Yes, definitely discharge the capacitor first — especially if it's a high-voltage one. A charged cap can damage your multimeter or give you completely wrong readings. To discharge it, you can short the leads using a resistor (like 1kΩ or 10kΩ), or a screwdriver with an insulated handle if it's a small electrolytic (nothing high voltage though — not safe). Also, for accurate readings: Take the capacitor out of the circuit if you can. In-circuit measurements are often wrong because of parallel components. Let the multimeter settle for a few seconds, especially with large caps. Make sure your test leads are making good contact. If your Meter has a "zero" or "rel" mode, use that to cancel out stray capacitance from the probes. And keep in mind, these DMM readings are just a ballpark — they won’t tell you if the cap has high ESR or leakage. For that, you'd need an ESR Meter. | |||||
| Answer to: Why Fluke multimeters are so expensive? | 3 Relevance | 4 months ago | maryjlee | Equipments | |
| ... etc. Tough housing, drop-tests, high-CAT safety ratings. High accuracy, true-RMS, stable calibration. Long lifespan, support and WArranty which reduce long-term cost. If you’re replacing a hobby-meter and don’t work in heavy duty applications, yes you might be fine with a cheaper brand. But if you need one tool that you can trust under serious conditions, the extra cost makes sense. | |||||
| Answer to: How to Locate a Short Circuit on a PCB? | 3 Relevance | 7 months ago | Paul | Theoretical questions | |
| ... the board, lifting one leg of suspected components (like capacitors or diodes) to see if the short clears. Electrolytic caps are a common culprit. Another simple method that’s helped me is the finger test or using a drop of isopropyl alcohol. Power the board with a current-limited supply (set low, so nothing burns), and often the shorted component will heat up faster than the rest. You can sometimes feel it with your finger or WAtch where the alcohol evaporates first. If the short is stubborn, I’ve also followed the divide and conquer approach—cutting tra ... | |||||
| Answer to: Suggestions for Good ATtiny85 Projects | 3 Relevance | 1 year ago | Admin | Circuits and Projects | |
| Here are 15 amazing project ideas you can create using the ATtiny85 microcontroller: LED Matrix AnimationProgram an LED matrix to display scrolling text or animations using the ATtiny85. Miniature Digital ThermometerBuild a small thermometer using a temperature sensor like LM35 or DS18B20 and display the data on a tiny OLED screen. IR Remote Control SystemDecode signals from an IR remote to control LEDs, fans, or other appliances. Sound Reactive LightsCreate an audio visualizer where LEDs blink in response to sound or music using a microphone module. Capacitive Touch SwitchMake a touch-sensitive button using a conductive surface and the ATtiny85, perfect for smart home switches. Portable Motion DetectorUse a PIR sensor to build a portable motion detection alarm system for security purposes. USB Volume ControllerTurn your ATtiny85 into a USB HID device to control your computer’s volume with a rotary encoder. Tiny Weather StationMeasure temperature and humidity with sensors like DHT11/DHT22 and display the readings on an OLED. Ultrasonic Distance MeterUse an ultrasonic sensor to measure distances and display them on a small display. Blinking Bicycle LightCreate a small, energy-efficient blinking tail light for a bicycle, powered by a coin cell battery. Minimalist USB Game ControllerBuild a simple game controller for retro-style games with buttons connected to the ATtiny85. PWM Fan Speed ControllerControl the speed of a DC fan using pulse-width modulation and a temperature sensor for feedback. ATtiny85 Robot BrainPower a small robot with an ATtiny85, controlling motors and sensors for basic navigation. Night Light with Light SensorCreate an automatic night light that turns on in low-light conditions using an LDR and LEDs. Tiny Digital StopwatchDesign a simple stopwatch with start, stop, and reset functions using push buttons and an OLED display. These projects highlight the versatility of the ATtiny85 and can help you learn more about electronics, programming, and sensors. This site is hands down the best for projects related to ATtiny85. So, definitely check it out. | |||||
| Answer to: what is "Display count" in a multimeter? | 3 Relevance | 1 year ago | Admin | Equipments | |
| ... to 1999. This means that when measuring voltage, current, or resistance, the highest reading you can see is 1999 units before the multimeter switches to a higher range or shows an overflow. Let’s say you are measuring voltage with a 2000-count multimeter. If the setting is on the 2V range, the Meter can show values up to 1.999V. If you measure 2.000V or higher, the multimeter will need to switch to a higher range to display that value, or it may show an error or “overload” indication if it’s beyond its capability. For example, if you try to measure 3V whi ... | |||||
