Notifications
Clear all
Search result for: WA 0852 2611 9277 Pesan Pembuatan Wall Panel Moulding Daerah Ciputat Kota Tangerang Selatan
| # | Post Title | Result Info | Date | User | Forum |
| Answer to: Running Arduino Directly from a Solar Panel | 18 Relevance | 8 months ago | Mehjabeen | Arduino | |
| Yes, it’s possible to power an Arduino directly from a solar Panel, but not reliably without extra components. A solar Panel’s voltage and current fluctuate with sunlight, which can cause the Arduino to reset or even get damaged. To make it work safely, you’ll need at least a regulator (buck or buck-boost) to keep the voltage stable, a blocking diode to prevent reverse current at night, and some capacitors or a supercapacitor to smooth out short drops in power. Without a battery, the project may still cut off under clouds or low light, so if continuous operation is required, even a small buffer battery or supercap is highly recommended. | |||||
| RE: Best Wireless module for my Home automation project | 13 Relevance | 2 years ago | Admin | Hardware/Schematic | |
| @neeraj-dev What do you mean by, "I’d like to have a WAll-mounted switch that can wirelessly communicate with an Arduino-based controller connected to the lights". Why do you need a WAll-mounted switch to make this project wireless? | |||||
| Running Arduino Directly from a Solar Panel | 12 Relevance | 8 months ago | SparkLab | Arduino | |
| Is it possible to power an Arduino project directly from a solar Panel without using a battery? I’m concerned about voltage fluctuations and whether the Arduino can handle them, or if additional components are required to make it work safely. | |||||
| Best Wireless module for my Home automation project | 7 Relevance | 2 years ago | Neeraj Dev | Hardware/Schematic | |
| Hi everyone! I'm an electrical engineering student who is new to home automation projects but has started working on one and needs some advice. I WAnt to create a system where I can control the lights in my house wirelessly. Specifically, I’d like to have a WAll-mounted switch that can wirelessly communicate with an Arduino-based controller connected to the lights. The goal is to replace the traditional wired switches with wireless ones that can send on/off commands to the Arduino, which will then control a relay to turn the lights on or off. I've researc ... | |||||
| Answer to: Is a capacitor really linear? | 6 Relevance | 10 months ago | Admin | Theoretical questions | |
| A capacitor is called linear because the relationship between the voltage across it and the current flowing through it is linear. The exponential curve you're seeing is its behavior over time, which is different. Here’s the breakdown: What "Linear" actually means here In circuit theory, a component is linear if it follows the rule of superposition and scaling.1 In simple terms: if you double the cause, you double the effect. For a capacitor, the relationship is defined by the equation 2I=CdtdV.3 This means the current (4I) is directly proportional to the rate of change of voltage (5dV/dt).6 So, if you double the current going into the cap, its voltage changes twice as fast. If you halve the current, its voltage changes half as fast. That direct, proportional relationship is what makes it a linear component. So why the exponential curve? That famous exponential curve shows the capacitor's voltage versus time when it's part of a circuit with a resistor (an RC circuit). It's not a direct graph of voltage vs. current. Think about what happens when you charge it: At the start, the capacitor is empty, so a large current flows in. As it charges, voltage builds up across it. This built-up voltage opposes the source, which reduces the voltage across the resistor, and therefore reduces the current flowing into the cap. So, the charging slows down as it gets fuller. This process of "charging slower and slower as it fills up" is what creates that exponential curve. The capacitor itself is still behaving linearly at any given instant, but the behavior of the whole circuit over time is exponential. So: Component's V-I relationship: Linear. (The physics of the cap itself). Circuit's V-T response: Exponential. (The behavior you see over time in an RC circuit). Hope that clears it up! | |||||
