Thermistors cost much less than the LM35 temperature sensor but require calibration due to their non-linear nature. At the same time, a thermistor is more accurate and precise(down to +/- 0.1°C) than an LM35(around +/- 0.5°C). LM35: Very easy to integrate with Arduino. You can read the output voltage directly using an analog pin, and with simple conversion (multiply by 100 to convert from mV to °C), you get the temperature. Thermistors: While they can be integrated, they often require additional components (like a resistor for a voltage divider) and more complex calculations to convert resistance to temperature. This can make them slightly more challenging to set up. Main Differences Feature LM35 Temperature Sensor Thermistor Type Integrated circuit (analog voltage output) Resistor (typically NTC or PTC) Output Outputs a linear voltage (10 mV/°C) Resistance changes non-linearly with temperature Temperature Range Typically -55 to +150 °C Varies, but generally -40 to +125 °C Accuracy Typically ±0.5 °C or better Can be very accurate, but depends on the Type and calibration Response Time Fast response time Generally fast but varies by design Ease of Use Simple to interface with Arduino (analog input) Requires more complex calculations for linearization Calibration Usually factory calibrated Often requires calibration and look-up tables for accuracy For most projects requiring precise temperature monitoring with reliable readings and ease of integration with Arduino, the LM35 is likely the best option. However, if you need the highest accuracy and can manage the additional complexity, consider using a thermistor P.S.: LM358 is an OP-AMP IC. LM35 is a temperature sensor.

... for beginners who are new to RF like me, and even the cheapest RF power meters cost hundreds of RMB. For electronics enthusiasts who follow the principle of "spend when you should, save when you can", DIYing an RF power meter is a great alternative. The first step WAs to define the functions and design the hardware circuit. To test RF power, a chip called a detector is required. I had not found a suitable option for a long time as it WAs my first time working with an RF detector, until I saw the power detection module on the E25-C test baseboard, which use ...

If your multimeter is acting strangely—like giving false continuity readings—my advice is to first check the manual. If you don’t have a physical copy, most manufacturers provide manuals online. Make sure the test probes are inserted into the correct sockets for the Type of measurement you're doing, and also verify that the batteries are in good condition and properly installed. If everything appears fine and the problem still exists, there’s a good chance the multimeter itself is faulty—especially if it’s a low-cost model. I wouldn’t recommend trying to repair it yourself, as defects might affect other functions and make it potentially unsafe to use. In such cases, it's better to replace it with a quality multimeter that’s safety-rated. This ensures greater reliability and safety, especially for household electrical work.

Decoupling capacitors are essential for stabilizing the power supply and suppressing noise in microcontroller and digital circuits. A common starting point is placing a 100 nF ceramic capacitor (X7R Type recommended) close to the Vcc and GND pins of each IC to handle high-frequency transients. To support sudden current demands and filter lower-frequency noise, it's also good practice to add a bulk capacitor—typically 1 µF to 10 µF—near the microcontroller or groups of ICs. The exact values depend on several factors, including the switching speed of the ICs, current consumption, and the quality of the PCB layout. Faster ICs may require additional smaller capacitors like 10 nF or 1 nF in parallel with the 100 nF to cover a broader frequency range. High-current circuits may benefit from larger bulk capacitors up to 47 µF. Proper placement is critical—capacitors should be located as close as possible to the power pins, with short, direct traces. Using a mix of capacitor values in parallel helps improve overall decoupling performance. While 100 nF is a solid default, evaluating layout and load conditions can help you fine-tune your choices for a more robust and reliable design.

Start with these simple IoT projectsJust Type the project name in Google search.Tip: The best WAy to dive into IoT projects is to use an ESP32 board and program it using Arduino IDE. Smart Plant Monitoring SystemMonitor soil moisture, temperature, and humidity, and send data to the server in real time. Wi-Fi Controlled Home AutomationUse an Arduino and a relay module to control lights and fans via a web browser IoT Weather Station with DHT & BMP SensorsCreate a weather station that logs humidity, temperature, and pressure online using sensors li ...

Piezoelectric sensors convert mechanical force into electrical energy. They work using the piezoelectric effect, which occurs in certain materials with a unique crystal structure. When you press, squeeze, or vibrate these materials, their internal charges shift, creating a voltage across the material. The amount of voltage they generate depends on several factors, including the amount of applied force, the Type of piezoelectric material used, and the sensor’s shape and thickness. If the vibrations match the material’s natural frequency, the voltage output can get a significant boost. Temperature also plays a role, as some materials are more stable than others. Additionally, how the sensor is connected to a circuit affects how much charge it stores and releases. That’s why these sensors are commonly found in devices like accelerometers, microphones, ultrasound equipment, and even energy-harvesting gadgets.

... sketch, it gets stored here permanently. It's like the hard drive on your computer – it keeps the code even when you turn the power off. So, when you power your Arduino back on, it knows what to do because the code is safe and sound in the Flash. SRAM (like RAM on your computer): This is your Arduino's working memory. When your code runs, it uses SRAM to store variables, temporary values, and all the stuff it needs to keep track of while it's running. Think of it like your computer's RAM – it's super fast, but it's volatile. That means when you turn the po ...

A boost converter is a Type of DC-DC converter that increases voltage while reducing current to maintain energy balance. It operates using an inductor, a switch (transistor), a diode, and a capacitor. When the switch is closed, current flows through the inductor, storing energy in its magnetic field. When the switch opens, the inductor resists the sudden drop in current and releases its stored energy. This energy combines with the input voltage, resulting in a higher output voltage. The diode ensures current flows in the correct direction, and the capacitor smooths the output voltage for a stable supply. By rapidly switching on and off, the boost converter efficiently steps up the voltage. The extra voltage comes from the inductor’s stored energy, making it useful in applications like battery-powered devices, LED drivers, and power supplies where a higher voltage is required.